











Because Lifes Depend on It. Email: info@dragonmfc.com
The examination beds are divided into general examination beds and gynaecological examination beds. The gynaecological examination bed is also known as a gynaecological operating table. It is an auxiliary medical equipment for hospitals, clinics, birth control stations and mobile gynaecological examination vans for various gynaecological examinations, diagnostic procedures and family planning examinations. The series of products can be adjusted to the actual situation in various positions of the patient during the consultation.
This product has a crossbar between headboard and footboard.
It is Stainless steel frame, foot with anti-noise rubber and back rest. It can be operated by gas-spring. High quantity sponge top with artificial leather cover (thickness: 3cm)
The design of this product focuses on humanization and comfort. The seamless design of the bed surface is more conducive to the cleaning of equipment and the cleaning and protection of medical staff.
The table consists of three parts, the headrest, the seating position and the removable foot section, which folds 90° when the foot extension is not in use.
Underneath the seating section of the table there is a waste collection tray that complies with hygiene standards.
The table has a retractable heel support system, this support section can be tilted to the left or right and when not in use it can be folded and concealed within the body of the table.
The leg extensions of the table can be removed and fixed and when not in use, they can be lowered with one simple movement.
The movement of the table up and down, back and seat is carried out by means of an electric motor which is placed in a system that does not distort the image.
The electric motor is operated by hand control or there is an option to make this system foot controlled.
The table has the capacity to carry patients of up to 120-160 kg without vibration.
The table has a towel suspension at the back which can be easily attached and removed if necessary.
The rising and lowering measures in the up-and-down movement of the table do not prevent the patient from reaching the table easily.
The total length of the table is 1800mm and the width is 550mm (20mm).
The minimum height of bed surface is 500mm, and the maximum height of bed surface is 1200mm.
Height adjustment range: 300 mm
Maximum load: 200kg
The bed surface is divided into 4 parts: head section, back section, hip section and auxiliary table. It has a pull-out hidden auxiliary table, which is easy to operate. The two sides of the bed are equipped with large arc armrests that can be opened to facilitate the patient's position adjustment. The foam sponge shell is soft and comfortable. The height and distance adjustable foot rest can be adjusted to the comfortable position according to the needs of patients and doctors. The table is equipped with a hand-held operating system to ensure trouble free operation. It can realize accurate linear movement, and the waterproof cap design can prevent sewage, dirt and static electricity, and make it use and move freely for years. All stainless steel shield, advanced spray plastic bed and column structure, easy to clean, anti pollution, seamless mattress, easy to clean, corrosion resistant, not easy to damage, antibacterial, anti-static, can effectively prevent patients from
bedsore.
A hidden sewage basin is arranged under the bed body, which can be easily pulled out or retracted, and is convenient for treating sewage and sundries
This product is used for parturient or general obstetric operation. It is especially suitable for the
examination and diagnosis of various instruments and microscopes in obstetrics and Gynecology
and urology.
This examination bed belongs to the field of medical equipment, its structure includes bed board, frame and bed leg, the bed board is set on the frame, said bed board includes back board and main board, the back board and main board are hinged to each other, said main board is installed on the frame on both sides of handrail, handrail side of the frame is installed on each side of the liftable leg support frame; the lower surface of the frame is installed on the guide slide, the guide slide is installed in its sliding connection The lower surface of the shelf body is installed with a guide rail, and a positioning seat is installed in the guide rail, and a footrest is installed below the positioning seat. Compared with the existing technology, the utility model has the features of reasonable design, simple structure, convenient use and good use effect.
Precautions.
Do not adjust the angle of each segmental plate while a patient is lying on the examination bed.
Remove all sewage from the bed after each use to keep the bed and accessories tidy and to prolong service life.
The examination bed must be serviced once a year
Multifunctional chest decompression and handle-operated exhaust gas drainage
Needle for puncture, including pen tube, needle for decompression and abduction and drainage cannula, decompression
The expiratory decompression needle from China factory consists of a needle base for expiratory and decompression puncture and a needle body.
The drainage cannula consists of the base of the drainage cannula and the body of the cannula.
Pneumatic needle for puncture and positioning in the drainage cannula, needle for decompression and abduction and drainage
The bushings are inserted together and positioned in the handle tube as one unit. Less
At the base of the pressure relieving puncture needle is a one-way air valve chamber and the one-way air valve chamber has
Valve type One-way valve • Insert the drain cannula into the front of the base of the decompression / extraction needle.
The center hole of the base, in the center, the utility model uses the handle tube type packaging.
It has good damage resistance, can be sterilized repeatedly and can simultaneously decompress and exhale from the chest cavity.
And drainage function, very suitable for quick rescue of the injured in the field。
The purpose of the China decompression needle manufacturer, if not sharp, is to decompress by converting a tension pneumothorax into an open pneumothorax. If you can do this quickly enough, a direct tube thoracostomy is a reasonable alternative. In a pinch, anything that opens that side of the chest will do its job - you can stick a knife in and find something to hold the hole open, maybe even a knife handle. Just a 14-hole China decompression needle is typically used ubiquitous in emergency rooms and hospitals, so it's the first helpful tool to get the job done quickly. You usually don't have time to scratch your head waiting for MacGyver's inspiration.
The basic principle of emergency decompression needles is to insert a catheter into the pleural space to create a channel for the air to escape and the accumulated pressure to escape. Although this approach is not the definitive treatment for tension pneumothorax, emergency needle decompression stops its progression and helps restore cardiorespiratory function slightly. For people with large pectoral muscles, China decompression needle length can be an issue and a long needle or vascular catheter may be needed.
Usually a large diameter vascular catheter is inserted into the midclavicular line between the second or third intercostal space. The use of a large diameter catheter is important because hemothorax can be associated with pneumothorax and the patient may require immediate IV fluids. A standing position may be helpful if it is not inappropriate due to the cervical spine or injury. This is the bridge to the definitive treatment of tubular thoracostomy. The catheter remains in place until the thoracic catheter is placed.
The procedure is as follows:
Locate anatomical landmarks and quickly prepare the puncture site with an iodine-based solution
Insert a large diameter decompression needle from China factory with catheter into the second intercostal space, above the third rib along the mid-clavicular line, 1-2 cm from the edge of the sternum (i.e. to avoid injury to the internal mammary artery)
Use a catheter or needle at least 5 cm long inserted perpendicular to the chest; however, it is important to note that in some patients the chest thickness may be greater than 5 cm and the inability to relieve symptoms may be associated with insufficient needle length ; longer pots are recommended (eg 8 cm)
Once the needle is in the pleural cavity, listen for the hissing of the escaping air to confirm the diagnosis of tension pneumothorax (note this on the patient's medical record); the air outlet may not be visible in places with high ambient noise levels
Remove the needle when the catheter is in place.
Secure the conduit in place and install the flicker valve.
Immediately after decompression, the needles begin preparing for thoracostomy tube insertion. Then reassess the patient, noting major aspects of trauma management (eg, airway, breathing, circulation). The hemothorax component is characteristic of tension pneumothorax; therefore, patients may require additional thoracostomy catheters.
Follow-up chest radiographs were taken to evaluate lung re-expansion, thoracostomy tube placement, and correction of mediastinal displacement .
A follow-up blood gas test (arterial blood gas) is required. All patients with tension pneumothorax were hospitalized.
The purpose of the needle is to allow the air that created the pneumothorax to escape, thus making room for the lung to re-expand.
The Foldable Stretcher can be folded and unfolded into a small size and has the characteristics of lightweight, small size, easy to carry, etc.
The Foldable Stretcher is made of high-strength aluminum alloy and Oxford leather material. It has the characteristics of lightweight, small size, easy to carry, easy to sterilize.
Therefore, whenever we sell a product we need to understand our buyer’s needs and then design for them. Because it will be our job as marketers to create an experience that people have that means they buy our product (or not) on their terms rather than ours on theirs.
There are several different types of stretchers, from small and light to large and heavy. There are three main types:
– The first type is a foldable stretcher that can be folded and then unfolded, similar to the way a yoga mat can be folded.
– This type of stretcher is made of a single piece of material, such as nylon or cotton. It’s like a regular stretcher, but it can be easily opened and closed.
The good news: there are plenty of other options
This is the first foldable stretcher I’ve seen. It’s a sturdy stroller attachment, made of high-strength aluminum alloy and Oxford leather material. It has the characteristics of lightweight, small size, easy to carry, easy to sterilize, etc.
In most situations, when you are using a foldable stretcher to create folds in objects that you want to bring somewhere and leave them there, folding the object on itself is not going to be the best option. This can be done by folding it on top of itself and then pinching the two ends together in a way that both ends are exposed (which will not fold the other side of the object).
A foldable stretcher is a tool for moving and positioning objects. Stretchers are intended to be made of aluminum alloy and Oxford leather material, which are durable and easy to clean. However, foldable stretchers can exist with low rigidity and be made of a variety of materials such as carpet, PVC or wood. The product must be sturdy without being heavy. It should not be used directly on the floor, but only on a flat surface that is stable enough to prevent it from slipping. The following precautions should be observed when using this product:
Always use the right side of the stretcher first before transporting any object on the left side, or on the right side when transporting objects in a right-handed manner:
People don’t want to fold their stretchers because of the trouble they take to fold and unfold them, or the effort it takes to do so.
People eat grains and cereals, it is inevitable that there are times when they get sick, and nowadays, with advanced medical care, when you get sick, of course, you will go to the hospital for treatment. Most people are treated through intravenous infusions to reduce inflammation and cough, etc. Therefore, when there is a high incidence of some diseases, we will see a large number of people sitting in the infusion room are dripping or waiting for the drip. There are even some elderly people who do not have enough nutrients in the heat of the day and go for nutrient delivery by IV. So for hospitals, IV stand are an indispensable tool. So what are the different varieties of IV stand, what materials are they made of, and are the prices of IV stand on the market now high? Let's talk about it briefly today!
Children's illness often makes all parents very heartbroken. Especially when the fever does not go down, parents will take their children to the IV drip, but look at the child is very mobile, so in the past, only the parents can only hold the child's hand throughout the IV drip, and the previous IV stand are for adults, did not take the child's small into account, and now the IV stand have special can provide for children to use, such as in the children's hospital infusion room inside the There are a large number of stand that are specifically provided for children's IV infusion, and the price of these children's IV stand is slightly higher. Not only can they be adjusted up and down according to the size of the child, they can also be adjusted according to the length of the arm, and they can also have the function of fixing the child's arm, which greatly liberates the parents and the child.
Most of the intravenous infusion is fixed directly on the seat, generally speaking, the left and right front and rear can be provided to four people for infusion use. But now there are also many are movable IV stand, these IV stand can be used one to one. The main function is that when some patients need to go to the bathroom, or when inpatients need to take a drip to the examination, they can move directly to their desired destination. Then the price of this kind of IV stand will be higher, in addition to the original structure, it also needs to have a wheel function underneath.
In fact, many of the IV stand used to be quite simple, and were made of wooden sticks, similar to coat hangers, to place the infusion. But because the loss of wood is relatively large, and the hospital because itself is the need for high-intensity sterilization, so the wooden loss will be particularly fast, now most of the use of stainless steel infusion rod, so that can be carried out for many years without changing, and can be for the role of corrosion to reduce the impact to a minimum. Therefore, the price of stainless steel IV stand is slightly higher.
Even simple IV stand need to take into account the actual use of the patient's problems, and also the handling, installation and other problems. Previously, the IV stand were all integral, so handling often required a special height of the carrier to handle. But now many IV stand manufacturers have made more disassembly features, not only that, but also more perfect support devices for smooth infusion paths according to the length and height of the patient's infusion, so that the patient can avoid backflow of blood due to low height or poor infusion, so the price of these patented IV stand is slightly higher.
In fact, nowadays, many hospitals, even some private hospitals, are quite attached to IV stand, and the price also varies greatly, some cheaper ones may be a hundred dollars, but some multi-functional ones need to be priced at several thousand dollars. Then you can buy in bulk by more than one to reduce the price of IV stand to some extent.
When the price of an item is getting higher, it directly means that the demand for that product is getting higher, and IV stand are one of them. The patient is already in pain, is it possible that the patient enjoys limited comfort in the process of treatment is also what many people are seeking now. From the previous single sitting straight to infusion, to now being able to lie down and be able to infuse according to their most comfortable angle and height is already an improvement. This is why the price of IV stand is getting higher and higher, especially for the many details that are now being improved to enhance the experience, with patented IV stand being a very good example.
Patients in the hospital are more concerned about their condition, the best treatment they can do, the best treatment effect, not the price of IV stand, but for the hospital or clinic, if you can use the best and most modern, the most humane IV stand, can provide more convenient services to patients of the equipment, so that is the real patient-oriented!
Subscribe to our email list and stay upto date with all your latest updates